Canvas Snaps Question

AC2717 · 05-24-2023, 06:59 PM

I have two snaps (on screws) that have come out of the side of the of my boat, and I have tried an adhesive to try and fill the hole with the screw snap but it has not worked.
Does anyone have any ideas or what have you done in the past.

ishoot308 · 05-24-2023, 07:38 PM

Quote:

Originally Posted by AC2717

I have two snaps (on screws) that have come out of the side of the of my boat, and I have tried an adhesive to try and fill the hole with the screw snap but it has not worked.
Does anyone have any ideas or what have you done in the past.

I have done this many times…clean the hole good to remove all the old adhesive you tried or drill a slightly larger hole. Then use JB Weld…you can get it in white, black and I believe gray. Fill the hole with JB using a toothpick. Let set up and shave off excess. Redrill proper size hole for snap. Obviously keep your repair area smaller than your snap perimeter so it’s not seen.

Good Luck!

Dan

8gv · 05-24-2023, 07:40 PM

Quote:

Originally Posted by AC2717

I have two snaps (on screws) that have come out of the side of the of my boat, and I have tried an adhesive to try and fill the hole with the screw snap but it has not worked.
Does anyone have any ideas or what have you done in the past.

The gentleman at Parafunalia in Gilford once told me to first try a longer screw.

If that fails, a larger diameter screw may be available but one must carefully drill the gelcoat hole wider so it won't crack when you screw it in.

SAB1 · 05-24-2023, 08:26 PM

Right. Drill hole the correct size for the screw and then use a countersink bit to open the top of the hole a bit so gel coat won’t crack.

LIforrelaxin · 05-25-2023, 09:39 AM

If you go to a shop that handle makes canvas tops often they have snaps with a few different screw sizes, and you can just move to the next larger screw size. I did that once many years ago on my fathers boat, and it simplified the need to try and refill the exsisting hole etc.

ishoot308 · 05-25-2023, 11:19 AM

AC2717;

I have found that the JB Weld fix I mentioned above ends up being much stronger than the original fiberglass / gel coat. At least that has been my experience with the many I have repaired.

If you have access to the backside of the fiberglass, they also sell a machine thread snap that you can put a nut and backing washer on. I have all kinds of snaps at my camp if you need some. Feel free to PM me if you want a few.

Dan

AC2717 · 05-25-2023, 05:58 PM

thank you everyone, I was able to use a bigger screw head snap for one of the snaps, but the whole on the second one was too big even for the larger snap screw, appears this was worked on before. I can get to the back of it so I am trying to find a snap head separate of the screw so I can use a stainless pan head machine screw to put through the Snape with a fender washer and nylon lock nut on the back side of the fiberglass. I went to Lowes and Heaths (trustworthy) no such luck on the snap heads

ishoot308 · 05-25-2023, 07:19 PM

Quote:

Originally Posted by AC2717

thank you everyone, I was able to use a bigger screw head snap for one of the snaps, but the whole on the second one was too big even for the larger snap screw, appears this was worked on before. I can get to the back of it so I am trying to find a snap head separate of the screw so I can use a stainless pan head machine screw to put through the Snape with a fender washer and nylon lock nut on the back side of the fiberglass. I went to Lowes and Heaths (trustworthy) no such luck on the snap heads

You mean like this? I have plenty if need a few!

AC2717 · 05-25-2023, 08:54 PM

Quote:

Originally Posted by ishoot308

You mean like this? I have plenty if need a few!

Yes that is exactly the set up I am looking to do are you up in the area?
That would be amazing

ishoot308 · 05-25-2023, 09:12 PM

Quote:

Originally Posted by AC2717

Yes that is exactly the set up I am looking to do are you up in the area?
That would be amazing

I’m on Welch island full time…. PM me and we can meet somewhere…

Dan

AC2717 · 05-25-2023, 09:20 PM

Quote:

Originally Posted by ishoot308

I’m on Welch island full time…. PM me and we can meet somewhere…

Dan

Sent - thank you!!!

AC2717 · 05-26-2023, 08:01 AM

A Giant THANK YOU to ISHOOT for giving me exactly what I needed to finish up my repairs, hopefully the last for the season!!!!

ISHOOT if you even need any assistance let me know

upthesaukee · 05-26-2023, 08:37 AM

And this is why I have been a proud member of the Winnipesaukee Forum since 2003. Neighbors / friends / boaters helping others.

Dave

The Real BigGuy · 05-26-2023, 10:19 AM

I would add that I have found that the best fix for a situation like this, if you can get to the back of the fiberglass is a wood block behind the fiberglass, caulk, and a longer screw.

Sent from my iPhone using Winnipesaukee Forum mobile app

05-24-2023, 06:59 PM	#1
AC2717 Senior Member Join Date: Apr 2007 Location: Maynard, MA & Paugus Bay Posts: 2,483 Thanks: 734 Thanked 337 Times in 252 Posts	Canvas Snaps Question I have two snaps (on screws) that have come out of the side of the of my boat, and I have tried an adhesive to try and fill the hole with the screw snap but it has not worked. Does anyone have any ideas or what have you done in the past. __________________ Capt. of the "No Worries"

05-25-2023, 09:39 AM	#5
LIforrelaxin Senior Member Join Date: May 2006 Location: Long Island, not that one, the one on Winnipesaukee Posts: 2,660 Thanks: 933 Thanked 821 Times in 473 Posts	If you go to a shop that handle makes canvas tops often they have snaps with a few different screw sizes, and you can just move to the next larger screw size. I did that once many years ago on my fathers boat, and it simplified the need to try and refill the exsisting hole etc. __________________ Life is about how much time you can spend relaxing... I do it on an island that isn't really an island.....

05-25-2023, 11:19 AM	#6
ishoot308 Senior Member Join Date: Feb 2008 Location: Gilford, NH / Welch Island Posts: 5,567 Thanks: 2,151 Thanked 4,602 Times in 1,769 Posts	AC2717; I have found that the JB Weld fix I mentioned above ends up being much stronger than the original fiberglass / gel coat. At least that has been my experience with the many I have repaired. If you have access to the backside of the fiberglass, they also sell a machine thread snap that you can put a nut and backing washer on. I have all kinds of snaps at my camp if you need some. Feel free to PM me if you want a few. Dan __________________ It's Always Sunny On Welch Island!!

05-25-2023, 05:58 PM	#7
AC2717 Senior Member Join Date: Apr 2007 Location: Maynard, MA & Paugus Bay Posts: 2,483 Thanks: 734 Thanked 337 Times in 252 Posts	thank you everyone, I was able to use a bigger screw head snap for one of the snaps, but the whole on the second one was too big even for the larger snap screw, appears this was worked on before. I can get to the back of it so I am trying to find a snap head separate of the screw so I can use a stainless pan head machine screw to put through the Snape with a fender washer and nylon lock nut on the back side of the fiberglass. I went to Lowes and Heaths (trustworthy) no such luck on the snap heads __________________ Capt. of the "No Worries"

05-26-2023, 08:01 AM	#12
AC2717 Senior Member Join Date: Apr 2007 Location: Maynard, MA & Paugus Bay Posts: 2,483 Thanks: 734 Thanked 337 Times in 252 Posts	A Giant THANK YOU to ISHOOT for giving me exactly what I needed to finish up my repairs, hopefully the last for the season!!!! ISHOOT if you even need any assistance let me know __________________ Capt. of the "No Worries"

05-24-2023, 08:26 PM	#4
SAB1 Senior Member Join Date: Feb 2012 Location: Tuftonboro Posts: 1,101 Thanks: 167 Thanked 281 Times in 208 Posts	Right. Drill hole the correct size for the screw and then use a countersink bit to open the top of the hole a bit so gel coat won’t crack.

The Following User Says Thank You to SAB1 For This Useful Post:
ApS (05-25-2023)

The Following User Says Thank You to LIforrelaxin For This Useful Post:
AC2717 (05-25-2023)

The Following User Says Thank You to ishoot308 For This Useful Post:
AC2717 (05-25-2023)

05-26-2023, 08:37 AM	#13
upthesaukee Senior Member Join Date: Jan 2003 Location: Alton Bay Posts: 5,495 Blog Entries: 2 Thanks: 2,326 Thanked 1,871 Times in 1,045 Posts	And why I have loved this Forum... And this is why I have been a proud member of the Winnipesaukee Forum since 2003. Neighbors / friends / boaters helping others. Dave __________________ I Live Here... I am always UPTHESAUKEE !!!!

The Following 6 Users Say Thank You to upthesaukee For This Useful Post:
AC2717 (05-26-2023), camp guy (05-26-2023), DRH (05-28-2023), ishoot308 (05-26-2023), Slickcraft (05-26-2023), thinkxingu (05-26-2023)

05-26-2023, 10:19 AM	#14
The Real BigGuy Senior Member Join Date: Apr 2004 Posts: 939 Thanks: 88 Thanked 345 Times in 201 Posts	I would add that I have found that the best fix for a situation like this, if you can get to the back of the fiberglass is a wood block behind the fiberglass, caulk, and a longer screw. Sent from my iPhone using Winnipesaukee Forum mobile app

The Following User Says Thank You to The Real BigGuy For This Useful Post:
ApS (05-26-2023)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode