|
Home | Forums | Gallery | Webcams | Blogs | YouTube Channel | Classifieds | Calendar | Register | FAQ | Donate | Members List | Today's Posts | Search |
|
Thread Tools | Display Modes |
|
07-11-2009, 05:42 PM | #1 |
Senior Member
Join Date: Jul 2005
Posts: 262
Thanks: 0
Thanked 23 Times in 11 Posts
|
Alpha One Outdrive Vibration
Boat has been running perfectly, no issues.
Until today. I'm getting a pretty strong vibration in the lower unit on occasion. It hasn't happened enough to know for sure exactly when, but it has happened when at very low throttle and turning sharply, as well as when in neutral at the dock with the lower unit all the way up. Under way seems to be fine. Any thoughts? Any hints for things I should look at / try? Thanks in advance! |
07-11-2009, 06:44 PM | #2 |
Senior Member
Join Date: Apr 2004
Posts: 305
Thanks: 254
Thanked 181 Times in 86 Posts
|
[QUOTE=MJM;99491]Boat has been running perfectly, no issues.
Until today. I'm getting a pretty strong vibration in the lower unit on occasion. It hasn't happened enough to know for sure exactly when, but it has happened when at very low throttle and turning sharply, as well as when in neutral at the dock with the lower unit all the way up. Under way seems to be fine. It sounds like your U joints are going bad. FYI you should NEVER run the engine with the outdrive "ALL THE WAY UP" This is a sure fire way to ruin the U joints and possibly have them lock up and explode. The all the way up position is also called "trailer" and it should only be used when the engine is off. I'd bring the boat to a good marine mechanic and have them pull the drive and check/replace the U joints |
07-11-2009, 06:54 PM | #3 |
Senior Member
Join Date: Apr 2004
Posts: 268
Thanks: 0
Thanked 14 Times in 8 Posts
|
MJM, by all the way up do you mean full trim and not trailer? If so, your problem may be the prop. Minor, and I mean Minor, damage to one or all of the blades can cause the vibrations you speak of. If it is an aluminum prop, it will have enough flex to even out at speed. Hard turns and idle speed are where these imperfections will translate to the wheel. Just my two cents.
__________________
Education is hanging around 'til you've caught on - Frost |
07-11-2009, 10:42 PM | #4 |
Senior Member
Join Date: Mar 2009
Location: Laconia NH
Posts: 128
Thanks: 24
Thanked 15 Times in 11 Posts
|
NEVER run and I/O (inboard/outboard) {outdrive equipted} boat with the drive tilted all the way up!!!! running it for 3 minutes can do some damage to the drivetrain.
I got my money bet on bad/worn out u-joints. the u-joints are constantly spinning because they are directly connected to the rear of the engine via engine coupler. when the engine runs, the u-joints spin due to the flywheel spinning (where the engine coupler is bolted to). you say the the outdrive is making vibration noises when tilted and when making turns. that is due to the u-joints are being flexed and binding when making turns or tilting/trimming the drive. your best bet to have the problem fixed is to take the boat to a marina/boat service person to have the u-joints replaced. also when it is being fixed get the gimbal bearing greased along with the transom, and have the engine alignment checked. im not sure where you are located so i cant recommend a service location near you. hope that helps, jst_4_kiks
__________________
Marine Technician - Learning Something New Every Day PM with any questions about marine repair |
07-12-2009, 06:58 AM | #5 |
Senior Member
Join Date: Jul 2004
Posts: 2,980
Thanks: 246
Thanked 739 Times in 440 Posts
|
U joint would be my guess too.
Below is what Mercruiser has to say about running in "Trailer" mode. It is pasted right out of the operators manual. "Power Trim allows the operator to adjust the drive angle, while underway, to provide the ideal boat angle for varying load and water conditions. Also, the Power Trim system “Trailering” feature allows the operator to raise and lower the drive unit for trailering, beaching, launching and low speed (below 1200 rpm engine speed), shallow water operation. CAUTION Never trim the drive unit UP/OUT using TRAILER switch while boat is underway at engine speeds above 1200 rpm. Use extreme caution when operating with drive unit raised. Severe damage to the drive unit may result if unit is raised beyond the gimbal ring support flanges at engine speeds above 1200 rpm." |
Sponsored Links |
|
07-12-2009, 12:06 PM | #6 |
Senior Member
Join Date: Jul 2005
Posts: 262
Thanks: 0
Thanked 23 Times in 11 Posts
|
Thanks to all for the feedback. VERY much appreciated.
The comment about it happening when fully up was more of a 'diagnosis' attempt - I was trying multiple scenarios to try to get the vibration to happen again so I could have a reasonable description for all you knowledgable folks as well as our mechanic. Aside from the occasional (OK, semi-frequent ) forgetting to lower it before starting the engine and having to do it right then, we wouldn't run it with the lower unit "trailered". I will post the results - thanks again everyone! |
07-12-2009, 06:24 PM | #7 |
Senior Member
Join Date: Jun 2008
Location: Portsmouth. RI
Posts: 2,231
Thanks: 400
Thanked 460 Times in 308 Posts
|
Most everyone seems to be going for the U-Joints...so I am going to suggest the Gimbal Bearing instead. Either way, you have to remove the drive to check either one. The check is pretty simple once the drive is off. 10 minutes to remove an Alpha I. BTW: It takes quite a bit more time to put it back on.
A bad Gimbal Bearing will "FEEL Grumbly/Rough"..(Not Satin Smooth and slightly tight as it should) when you put two or three fingers in the bearing bore and roll the bearing back and forth. Your hands will get greasy doing this. Bad U-Joints will feel Sloppy/Loose/Clunky.. when rocked back and forth. Either way the drive has to be removed to do the check. |
Bookmarks |
|
|