Quote:
|
Originally Posted by LIforrelaxin
1) Dealership I bought the boat at suggested that they could take the boat strip down the gel coat in the effected area and re-gel coat it.....I am sure this would work but what about the rest of the Hull?
2) Was told by another dealership.... awww its only cosmetic I would leave it, fixing it and bottom coating it will only devalue the boat....
3) By two Fiberglass repair facilities it was suggested that the affected area be sanded down and the blisters cleaned up and then refilled with gel and smoothed. And then to seal the hull from the waterline down with a product from Interlux called interprotect 2000.
a) now one facility recomended doing nothing after the coating of
interprotect
b) the second facility recomended putting a product call VC
performance over the interportect coating
Does anyone have any experience or recomendations on any of this?
Has anybody dealt with either Unique Boat Restoration in Moultonboro or a company called North East Fiberglass.....
Thanks in advance for any advice......
|
Well after reading many articles and talking with many people here is what I found, hopefully be posting what I found someone will be able to read this thread in the future and get some guidence.
1) From what I have read the idea that Blisters are only cosmetic is a somewhat short sighted view. What I got from the reading I did was that sure enough when blisters start they are inocent enough. It is the effect that the water has over time reacting with the resins and so fourth that causes the damage. In the Northeast we are lucky from the stand point that we take our boats out every year for several months which gives the blisters a chance to dry out and slow the damage rate. But eventually a great deal of damage can occur leading to hull integrity damage. This is an issue that will never get better once it has started.
2) The permeability of the gel coat as some other posters have indicated is dependant on the types of Resin used. There where 3 main types that where consistently talked about. Not wanting to get any of that wrong I am not going to post that, but if you search the web there is more then enough information out there.
3) Along with the permeablity of the resins used as another poster suggested bad workmanship leading to fiber glass not getting sufficiently soaked in resin there for causeing bonding issues to the gelcoat and lead to blisters.
4) Once the blisters start you need to pay attention to them. What appears to have happend in my case is that this all started inocently with a single blister, that got water traped and froze over the winter, causing a split in the gel coat. From there water was able to get in easier and I think caused the blistering to spread. (this is my theory) As for when it is time to do something about the blistering that is a personal call, I would say better sooner then later.
Now as for what to do to fix the problem.
First let me say that I didn't find anyone or anything that said they could 100% do something and the blisters would never come back.
when I first started this endevor I stated the 4 recomendations I had gotten as it turns out the recomendations from the two dealers I talked to where not, in my mind the best solutions. So right away after reading a few articles I quickly ruled out, just doing nothing, as well as just sanding down and re-gelling the effected area. Nor did I find any published work to support those two fixes.
What I did find articles on, and in fact was recomended by the manufacture is to repair the blister section of hull and then apply an epoxy barrier to the entire hull below the waterline. What I found interesting was what was writen about the necessity to fix the blistered section of hull. It is not just simply good enough to let the boat sit and dry out and then cover the hull with the epoxy barrier.... It is suggested that you sand down the blisters and let everything dry out. they even make a tool to test the mosture content of the gel coat and fiber glass (there were actually a couple of ways to do this, up to and including coreing out a section of the hull....that is the most damaging way to do it luckily there are less damaging ways)... once everything is dried out sufficiently, the surounding gel coat and fiberglass needs to be repaired if any damage is present. Once all repairs are made then the barrier can be applied.
I don't know how many different barrier coats are available. I found that one was recomended consistently. But there are certain to be others. The barrier coat does appear to be tricky to apply and appears to be best handled by a pro. There are time constriaints as to how quickly coats must be applied and from start to finish how long the whole process can take.
After the barrier coat, I have found some mixed advice, some say it is fine by itself. While others say you should apply something over it. I personally think this has more to do with cometics from what I can tell. The product I plan to have used is more of a matte finish, and what has been recomend to put over it has been something that will have a bit more of a semi gloss finish. While the barrier appears to be very hard and doesn't require maintance unless it scraped up, which would be hard in my estimation the stuff cures extremely hard. I worry that anything put over it my eventually wear down and need to be re-applied down the road.
My quess is I will not have anything put over the barrier. But I believe that will also be dictated by who will do the work, which I am still trying to decide on. This is not a inexpensive endeavor to start on, and I want to make sure I have confidence in the person doing the work. Also because of the expense it you do and I have considered the age of the boat, how long you plan to keep it, and how much of an issue the blisters are. In my case I plan to have the boat for a while, and the section of hull effected is pretty big and quite blistered.
I will let you all know how things turn out in the spring once the work is done.
The information in this post is my interpretation of the information I found on the subject, others are certain to have different views, I offer this simply as advice.